NUT,PLAIN,HEXAGON

WVX 771-229-1432 [email protected] See specification sections C and E A Stand-Alone Receiving Report - Certifications Combo - Receiving Report & Invoice - Material N/A TBD TBD N39040 - Certifications, S4306A - Material TBD 133.2 N/A N/A N39040 - Certifications N/A N/ A See DD FORM 1423 [email protected] One year from date of delivery One year from date of delivery 1. DD1423 Data Item A001 (Inspection and Test Plan) may be waived if already onfile at NAVSUP WSS Mechanicsburg. 2. Portsmouth NSY's DODAAC has changed from N00102 to N50286. Any reference to N00102 within this order should be updated to N50286. 3. The following proposed delivery schedule applies: Submission of Certification Data CDRLs will be on or before 20 days prior to scheduled delivery. PNSY review/acceptance of Certification CDRLs 6 working days after receipt of Certification DD 1423 CDRLs. Final delivery of material will be on or before 365 days after effective date of the resulting contract. 4. Early delivery is acceptable at no additional cost. 5. Any contract awarded because of this solicitation will be a "DX/DO" rated order certified for national defense use under the Defense Priorities and Allocations System (DPAS). 6.NAVSUP WSS Mechanicsburg will be considering past performance in the evaluation of offers. 7.The Production Lot Test (PLT) requirement refers to the "additional" fastener required by the technical data package. \ 1. SCOPE 1.1 The material covered in this contract/purchase order will be used in a crucial shipboard system. The use of incorrect or defective material would create a high probability of failure resulting in serious personnel injury, loss of life, loss of vital shipboard systems, or loss of the ship itself. Therefore, the material has been designated as SPECIAL EMPHASIS material (Level I, Scope of Certification, or Quality Assured) and special control procedures are invoked to ensure receipt of correct material. 2. APPLICABLE DOCUMENTS 2.1 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the text of this contract/purchase order must take precedence. Nothing in this contract/purchase order, however, must supersede applicable laws and regulations unless a specific exemption has been obtained. 2.2 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.2.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.2.2 The documents and drawings listed below under DRAWING NO. are not provided with this Contract/Purchase order. DRAWING NO CAGE REV DISTR CD ;366-59531 66935 E B; 2.2.3 Specification Revisions - The specification revisions listed under "Documents References" below are the preferred revision. Older and/or newer r evisions are acceptable when listed within Contract Support Library Reference Number CSD155 in ECDS (Electric Contractor Data Submission) at: ht tps://register.nslc.navy.mil/. This is to allow Contractors to use certain acceptable older specification revisions to purge their existing stock of material certified to those older revisions or to use newer specification revisions when material is certified to newly released revisions,without requiring the submittal of waiver/deviation requests for each specification revision on every contract. Revisions of specifications reflecting editorial and/or re-approval (e.g. E2009, R2014, etc.) are considered inconsequential, but are acceptable when their revisions are listedwithin CSD155 or elsewhere within this contract. DOCUMENT REF DATA=FED-STD-H28 B A DOCUMENT REF DATA=FED-STD-H28 B A DOCUMENT REF DATA=ANSI/ASQ Z1.4 A DOCUMENT REF DATA=QQ-N-286 G A DOCUMENT REF DATA=MIL-STD-792 F A DOCUMENT REF DATA=MIL-DTL-1222 J A DOCUMENT REF DATA=MIL-STD-2132 D F DOCUMENT REF DATA=…