STOP LUG,LUG

FA 771-229-0460 [email protected] B Invoice and Receiving Report (Combo) Inspection / Acceptance Point: Source TBD TBD TBD TBD N/A N/A TBD N/A N/A N/A N/A [email protected] NOTE: This is not a true FMS Requirement/contract. Due to system limitations, the FMS designation could not be removed. Contractor is liable for all shipping expenses to DODAAC location(s) specified within Consignment Instruction notes in contract. TO VIEW THE DRAWINGS: Go to www.sam.gov Click: Contract Opportunities and enter the solicitation number. This gives access to the Electronic Solicitation. Drawings can be viewed or downloaded. GOVERNMENT SOURCE INSPECTION per FAR 52.246-2 IS REQUIRED. DELIVERY 90 DAYS. All contractual documents (i.e. contracts, purchase orders, task orders,delivery orders and modifications) related to the instant procurement areconsidered to be "issued" by the Government when copies are either depositedin the mail, transmitted by facsimile, or sent by other electronic commercemethods, such as email. The Government's acceptance of the contractor'sproposal constitutes bilateral agreement to "issue" contractual documents asdetailed herein. \ 1. SCOPE 1.1 This contract/purchase order contains the requirements for manufacture of the STOP LUG,LUG . 2. APPLICABLE DOCUMENTS 2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.1.1 Documents, drawings, and publications supplied are listed under "Drawing Number". These items should be retained until an award is made. 2.1.2 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.1.3 The "Document Changes" section provides supersessions/changes to referenced documents. 2.2 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the drawings shall take precedence. Nothing in this contract/purchase order, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. DRAWING DATA=56293 OD D 0000.A 0018500 DRAWING DATA=56293 OD D 0000.B 0021965 DRAWING DATA=56293 OD D 0000.C 0024872 DRAWING DATA=56293 OD D 0000.COV 0038973 DRAWING DATA=56293 OD D 0000.D 0026986 DRAWING DATA=56293 OD D 0000.II 0015689 DRAWING DATA=56293 OD D 0000.III - 0026790 DRAWING DATA=56293 OD D 0000.IV - 0008318 DRAWING DATA=56293 OD D 0000.V - 0037946 DRAWING DATA=56293 OD D 0001.1 - 0039238 DRAWING DATA=56293 OD D 0001.2 - 0024017 DRAWING DATA=56293 OD D 0002.1 0019410 DRAWING DATA=56293 OD D 0003.1 0028858 DRAWING DATA=56293 OD D 0003.2 - 0028844 DRAWING DATA=56293 OD D 0003.3 - 0031180 DRAWING DATA=56293 OD D 0003.4 - 0032024 DRAWING DATA=56293 OD D 0003.5 - 0012193 DRAWING DATA=56293 OD D 0004.1 0027622 DRAWING DATA=56293 OD D 0004.2 - 0021502 DRAWING DATA=56293 OD D 0004.3 - 0015474 DRAWING DATA=56293 OD D 0005.1 0028854 DRAWING DATA=56293 OD D 0005.2 - 0033261 DRAWING DATA=56293 OD D 0005.3 - 0035235 DRAWING DATA=56293 OD D 0005.4 0036465 DRAWING DATA=56293 OD D 0005.5 0021294 DRAWING DATA=56293 OD D 0005.5A1 - 0012105 DRAWING DATA=56293 OD D 0005.5A2 0061537 DRAWING DATA=6236107 B D B 0426184 3. REQUIREMENTS 3.1 Manufacturing and Design - The STOP LUG,LUG furnished under this contract/purchase order shall meet the material and physical requirements as specified ;P/N: 6236107-002 cage 53711; . 3.2 Marking - Unless marking requirements are specified by a document or drawing cited in this solicitation all items delivered under this contract/purchase order shall be marked and identified in accordance with the applicable Military Standards and Specifications as follows: Mechanical Parts, Assemblies and Equipments - MIL-STD-130 Electrical and Electronic Parts - MIL-STD-1285, Method 1. Electrical and Electronic Parts and Assemblies not covered by MIL-STD-1285-use MIL-STD-130. Electro…