DUST PLUG

FEB +1 771-229-0462 [email protected] B Invoice and Receiving Report (Combo) N/A TBD TBD TBD TBD N/A N/A TBD N/A N/A N/A N/A [email protected] The purpose of this amendment is to add drawing 2330005 to the bid set. CALLOUT OF P/N: 17-1 CRIMPING TOOL WENT OBSOLETE. MFG. P/N: 31-BHAS BEEN APPROVED FOR USE. \ TO VIEW THE DRAWINGS: Go to www.https://beta.sam.gov/ Click: Contract Opportunities and enter the solicitation number. This gives you access to the Electronic Solicitation. Drawings can be viewed or downloaded. GOVERNMENT SOURCE INSPECTION per FAR 52.246-2 IS REQUIRED. DELIVERY_____90__________DAYS. All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications) related to the instant procurement are considered to be "issued" by the Government when copies are either deposited inthe mail, transmitted by facsimile, or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein. 1. SCOPE 1.1 This contract/purchase order contains the requirements for manufacture of the DUST PLUG . 2. APPLICABLE DOCUMENTS 2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.1.1 Documents, drawings, and publications supplied are listed under "Drawing Number". These items should be retained until an award is made. 2.1.2 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.1.3 The "Document Changes" section provides supersessions/changes to referenced documents. 2.2 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the drawings shall take precedence. Nothing in this contract/purchase order, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. DRAWING DATA=1960713 F D DRAWING DATA=1960713 1N D DRAWING DATA=2330005 A DW D DRAWING DATA=2330005 1N D DRAWING DATA=3044652 DW D DRAWING DATA=3044652 PL D DRAWING DATA=3516 E WS D 3. REQUIREMENTS 3.1 Manufacturing and Design - The DUST PLUG furnished under this contract/purchase order shall meet the material and physical requirements as specified ;NAVSEA P/N: 3044652 (DUST, PLUG) MODIFICATIONS TO DANFOSS/HANSEN LINE P/N:: SDC3HK CAGE CODE (0X660). MUST ADHERE TO THE REGS/SPECS WITHIN DRAWING 3044652. MFG. CALLOUT OF P/N: 17-1 CRIMPING TOOL WENT OBSOLETE. MFG. P/N: 31-B HAS BEEN APPROVED FOR USE.; . 3.2 Marking - Unless marking requirements are specified by a document or drawing cited in this solicitation all items delivered under this contract/purchase order shall be marked and identified in accordance with the applicable Military Standards and Specifications as follows: Mechanical Parts, Assemblies and Equipments - MIL-STD-130 Electrical and Electronic Parts - MIL-STD-1285, Method 1. Electrical and Electronic Parts and Assemblies not covered by MIL-STD-1285-use MIL-STD-130. Electronic Equipment - MIL-STD-454 Requirement Number 67. Electrical Equipment - MIL-P-15024/5 (SHIPS) 3.3 Configuration Control - MIL-STD-973 entitled "Configuration Management", Paragraph 5.4.8, Configuration Control (Short Form Procedure), is hereby incorporated. The Contractor shall submit all Engineering Change Proposals in accordance with MIL-STD-973, Paragraph 5.4.8.2 and Appendix D. Requests for Deviations shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.3 and Appendix E. Requests for Waivers shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.4 and Appendix E. (Original and two copies shall be submitted to Contracting Officer, NAVICP-MECH, P. O. Box 2020, Mechanicsburg Pa. 17055-0788.) 4. QUALITY ASSURANCE 4.1 Responsibility for Inspection - Unless otherw…