REGULATOR,TEMPERATU

WVC 564-230-3066 [email protected] See specification sections C and E B Stand-Alone Receiving Report - Certifications Combo - Receiving Report & Invoice - Material NA TBD TBD N39040 - Certifications, S4306A - Material TBD 133.2 NA NA N39040 - Certifications NA NA [email protected] One year from date of delivery. One year from date of delivery. Solicitation amended to extend closing and add clauses. \ This amendment is issued to increase QTY to 10 and extend closing date to 12 Feeb 2024. 1. Data Item A001 (inspection and Test Plan) may be waived if already on file at NAVSUP WSS Mech. 2. This soliciatations is and reulting award will be issued IAW EAF. 3. This is a rated order certified for national defense use,and the Contractor will follow all the requirements ofthe Defense Priorities and Allocations Systemregulation (15 CFR 700). 1. SCOPE 1.1 The material covered in this contract/purchase order will be used in a crucial shipboard system. The use of incorrect or defective material would create a high probability of failure resulting in serious personnel injury, loss of life, loss of vital shipboard systems, or loss of the ship itself. Therefore, the material has been designated as SPECIAL EMPHASIS material (Level I, Scope of Certification, or Quality Assured) and special control procedures are invoked to ensure receipt of correct material. 2. APPLICABLE DOCUMENTS 2.1 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the text of this contract/purchase order must take precedence. Nothing in this contract/purchase order, however, must supersede applicable laws and regulations unless a specific exemption has been obtained. 2.2 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.2.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.2.2 The documents and drawings listed below under DRAWING NO. are not provided with this Contract/Purchase order. DRAWING NO CAGE REV DISTR CD ;3337765 59364 E B; 2.2.3 Specification Revisions - The specification revisions listed under "Documents References" below are the preferred revision. Older and/or newer r evisions are acceptable when listed within Contract Support Library Reference Number CSD155 in ECDS (Electric Contractor Data Submission) at: ht tps://register.nslc.navy.mil/. This is to allow Contractors to use certain acceptable older specification revisions to purge their existing stock of material certified to those older revisions or to use newer specification revisions when material is certified to newly released revisions,without requiring the submittal of waiver/deviation requests for each specification revision on every contract. Revisions of specifications reflecting editorial and/or re-approval (e.g. E2009, R2014, etc.) are considered inconsequential, but are acceptable when their revisions are listedwithin CSD155 or elsewhere within this contract. DOCUMENT REF DATA=FED-STD-H28 A DOCUMENT REF DATA=FED-STD-H28 B A DOCUMENT REF DATA=ANSI/ASQ Z1.4 A DOCUMENT REF DATA=MIL-STD-792 F A DOCUMENT REF DATA=MIL-STD-2035 A A DOCUMENT REF DATA=SAE AMS 5659 S A DOCUMENT REF DATA=ISO_9001 A DOCUMENT REF DATA=ISO10012 A DOCUMENT REF DATA=ISO/IEC 17025 A DOCUMENT REF DATA=MIL-I-45208 A A DOCUMENT REF DATA=MIL-STD-45662 A A DOCUMENT REF DATA=ANSI/NCSL Z540.3 A DOCUMENT REF DATA=0900-LP-001-7000 C DOCUMENT REF DATA=S9074-AQ-GIB-010/248 A DOCUMENT REF DATA=T9074-AS-GIB-010/271 A DOCUMENT REF DATA=S9074-AR-GIB-010A/278 (CHG A) A 3. REQUIREMENTS 3.1 ;Pressure Transducer must be in accordance with Allied Signal drawing 3337765, part number 3337765-1, except as amplified or modified herein.; 3.2 Material for Parts Requiring Certification - Quantitative chemical and mechanical analysis is…